New Construction Electrical in West Hollywood, CA

Buzo Electric Co provides new construction electrical in West Hollywood, CA for custom homes, full renovations, and commercial build-outs. We are a C-10 electrical contractor and integrator, which means the same licensed firm that runs your 400A service also programs your Lutron, Control4, or Josh AI system. Architects, interior designers, GCs, and homeowners bring us in at design-build stage to engineer the load calculation, the rough-in, and the control system as one scope. Contact us to put one accountable firm on the electrical and integration package for your West Hollywood project.

Our New Construction Electrical Services in West Hollywood, CA

Our scope for new construction electrical in West Hollywood, CA runs from the service entrance to the last keypad. We design and install:

• New-construction and custom-home electrical. Design-build with the architect and GC: load calculations, panel schedules, rough-in, trim-out, and final commissioning as one documented scope.
• 200A and 400A service upgrades and Span smart panels. We size the service for the real load, not a guess, and set subpanels and a Span smart panel where circuit-level monitoring and control earn their place.
• Lutron lighting control and motorized shades. We engineer each scene, place keypads with the designer, and wire the low voltage backbone during rough-in so trim-out is clean.
• Control4 and Josh AI whole-home automation. Design, programming, and ongoing support from the firm that pulled the wire, so the system and the electrical plan match.
• Structured wiring, home theater, and whole-home audio and video. Rack, head end, media rooms, and distributed AV planned alongside the branch circuits that feed them.
• Generac standby power and EV charging. Whole-house automatic standby generators with an automatic transfer switch, plus Level 2 chargers and Tesla Wall Connector installation on properly sized circuits.

Why West Hollywood, CA Homeowners Choose Us

We are the integrator-electrician: the only firm on the project that holds the C-10 and programs the Control4 or Josh AI system. On a typical new build, that collapses two trades and a coordination problem into one contract. The lighting control keypads land where the circuits actually are. The rack and head end get dedicated power and cooling because the same engineer drew both.

We work in whole projects: new builds, full renovations, estate upgrades, and commercial build-outs. We do not run service calls. Specifiers get technical fidelity from us, in writing: amperage, load calculations, brand and model lines, how each scene is engineered, and what a 400A service makes possible for the property.

The local housing stock makes this scope matter. The typical West Hollywood home was built around 1965, per U.S. Census Bureau ACS estimates, so a full renovation here usually means replacing the service, the panel, and the branch wiring, not patching around them. The electrical and integration package should be engineered to the standard of the property. Buzo Electric Co, CSLB C-10 #1048529.

Serving West Hollywood, CA and Nearby Areas

Our shop sits in West Adams, Los Angeles, a direct run up to West Hollywood. Beyond West Hollywood we take on projects in Los Angeles, Beverly Hills, Santa Monica, Malibu, Pacific Palisades, Brentwood, Bel Air, Culver City, Marina del Rey, Venice, Calabasas, Hidden Hills, and Manhattan Beach, CA. Same scope everywhere: design-build electrical plus integration under one C-10 license.

New Construction Electrical Questions We Hear in West Hollywood, CA

When should the electrical contractor join a new-build project?

At design development, before permit drawings are final. The load calculation drives the service size, the panel locations, and the conduit runs, and the lighting control plan drives keypad and shade wiring at rough-in. Bringing us in early lets the architect and GC lock those decisions once instead of revising them in the field.

Do I need a 400A service for a custom home?

It depends on the load calculation, not the square footage alone. A home with electric ranges, heat pump systems, a standby generator transfer switch, and two Level 2 EV chargers can justify 400A; many homes run well on a 200A service with a Span smart panel managing the loads. We run the numbers during design-build and show you the calculation before anyone orders gear.

Can one firm handle both the electrical and the automation?

Yes, and that is the point of our model. We hold the C-10 license and program the Control4, Josh AI, and Lutron systems ourselves, so the structured wiring, low voltage, and line voltage scopes come from one set of drawings. There is no handoff between an electrician and a separate AV firm, and no gap in responsibility when a scene does not behave as specified.

Does standby power fit into a new-construction scope?

It fits best there. A Generac whole-house standby generator with an automatic transfer switch is simplest to engineer when the service, panels, and gas or fuel supply are being designed together. We size the generator against the same load calculation that sizes your service, so the backed-up circuits match how the home actually runs. Grid demand in Los Angeles is not getting smaller; standby power is a design decision, not an afterthought.

Get Started

If you are planning a new build, full renovation, or commercial build-out, contact us to discuss new construction electrical in West Hollywood, CA. Send the plans, and we will respond with a scoped proposal covering the service, the load calculation, and the integration package. One licensed firm, one set of drawings, one point of accountability from rough-in to the last programmed scene.

Related guide: new construction electrical — Complete Guide

Prefer to talk it through? Call (323) 252-7498 — a quick call is usually the fastest way to get a straight answer for your situation.